MX25L12835F DATASHEET full user guide

GENERAL DESCRIPTION
MX25L12835F is 128Mb bits serial Flash memory, which is configured as 16,777,216 x 8 internally. When it is in
two or four I/O mode, the structure becomes 67,108,864 bits x 2 or 33,554,432 bits x 4. MX25L12835F feature a
serial peripheral interface and software protocol allowing operation on a simple 3-wire bus while it is in single I/O
mode. The three bus signals are a clock input (SCLK), a serial data input (SI), and a serial data output (SO). Serial
access to the device is enabled by CS# input.
When it is in two I/O read mode, the SI pin and SO pin become SIO0 pin and SIO1 pin for address/dummy bits input
and data output. When it is in four I/O read mode, the SI pin, SO pin, WP# and RESET# pin become SIO0 pin,
SIO1 pin, SIO2 pin and SIO3 pin for address/dummy bits input and data output.
The MX25L12835F MXSMIO (Serial Multi I/O) provides sequential read operation on whole chip.
After program/erase command is issued, auto program/erase algorithms which program/erase and verify the specified
page or sector/block locations will be executed. Program command is executed on byte basis, or page (256
bytes) basis, or word basis for erase command is executed on sector (4K-byte), block (32K-byte), or block (64K-byte),
or whole chip basis.
To provide user with ease of interface, a status register is included to indicate the status of the chip. The status read
command can be issued to detect completion status of a program or erase operation via WIP bit.
Advanced security features enhance the protection and security functions, please see security features section for
more details.
When the device is not in operation and CS# is high, it is put in standby mode.
The MX25L12835F utilizes Macronix’s proprietary memory cell, which reliably stores memory contents even after
100,000 program and erase cycles.

FEATURES
GENERAL
• Serial Peripheral Interface compatible — Mode 0 and Mode 3
• Single Power Supply Operation
– 2.7 to 3.6 volt for read, erase, and program operations
• 128Mb: 134,217,728 x 1 bit structure or 67,108,864 x 2 bits (two I/O mode) structure or 33,554,432 x 4 bits (four
I/O mode) structure
• Protocol Support
– Single I/O, Dual I/O and Quad I/O
• Latch-up protected to 100mA from -1V to Vcc +1V
• Low Vcc write inhibit is from 2.3V to 2.5V
• Fast read for SPI mode
– Support clock frequency up to 133MHz for all protocols
– Support Fast Read, 2READ, DREAD, 4READ, QREAD instructions.
– Configurable dummy cycle number for fast read operation
• Quad Peripheral Interface (QPI) available
• Equal Sectors with 4K byte each, or Equal Blocks with 32K byte each or Equal Blocks with 64K byte each
– Any Block can be erased individually
• Programming :
– 256byte page buffer
– Quad Input/Output page program(4PP) to enhance program performance
• Typical 100,000 erase/program cycles
• 20 years data retention
SOFTWARE FEATURES
• Input Data Format
– 1-byte Command code
• Advanced Security Features
– Block lock protection
The BP0-BP3 and T/B status bit defines the size of the area to be protection against program and erase instructions
– Advanced sector protection function (Solid and Password Protect)
• Additional 4K bit security OTP
– Features unique identifier
– factory locked identifiable, and customer lockable
• Command Reset
• Program/Erase Suspend and Resume operation
• Electronic Identification
– JEDEC 1-byte manufacturer ID and 2-byte device ID
– RES command for 1-byte Device ID
– REMS command for 1-byte manufacturer ID and 1-byte device ID
• Support Serial Flash Discoverable Parameters (SFDP) mode
HARDWARE FEATURES
• SCLK Input
– Serial clock input

SI/SIO0
– Serial Data Input or Serial Data Input/Output for 2 x I/O read mode and 4 x I/O read mode
• SO/SIO1
– Serial Data Output or Serial Data Input/Output for 2 x I/O read mode and 4 x I/O read mode
• WP#/SIO2
– Hardware write protection or serial data Input/Output for 4 x I/O read mode
• RESET#/SIO3
– Hardware Reset pin or Serial input & Output for 4 x I/O read mode
• PACKAGE
-8-pin SOP (200mil)
-16-pin SOP (300mil)
-8-land WSON (6x5mm)
-8-land WSON (8x6mm)
– All devices are RoHS Compliant

[wp-embedder-pack width=”120%” height=”900px” download=”all” download-text=”” attachment_id=”777″ /]